Go To Cheap Store for Check Price Now !!
This generator is ideal for camping and powering small-scale household appliances like TVs or computers. 2-stroke, 63cc engine has recoil start and transistorized ignition. Meets EPA standards. Engine: 2-Stroke, 63cc, Rated Watts: 1,000, Rated Watts LP: N/A, Rated Watts NG: N/A, Surge Watts: 1,200, Surge Watts LP: N/A, Surge Watts NG: N/A, Run Time: 4.5 Hours at 1/2 Load, Receptacles (qty.): 2, Noise Level (dB): 69, Fuel Type: Gasoline, Fuel Capacity (gal.): 1, Start Type: Recoil, Dimensions L x W x H (in.): 15 x 16 x 13
Readmore
Technical Details
- 1000 running watts/1200 max watts- ETQ 2 stroke air cooled OHV engine
- 1 gallon fuel tank provides 5.5 hours of run time at 50% load
- Less than 65 db
- Non-CARB Compliant/Not For Sale In California
See more technical details
By Amazonian (Around the World)
Got this about a month ago for tailgates. Haven't put much time on it yet, but here are some intitial comments:
1) Mine did not come with a DC plug / adapter. Called ETQ and they said that the newer ones do not have that feature.
2) There is an error in the manual. It says to use 10w30 oil. That is NOT CORRECT. Use only 2 cycle oil. The manual is wrong.
I tested the sound level using my radio shack sound level meter and found that at 23 feet it produced around 59 dbA and at 9 feet it produced about 67 dbA. I would characterize the sound as louder than the Honda EU2000 / EU1000, but overall not too objectionable as it's kind of a low pitch sound. It's definitely why the unit is less expensive than the Honda EU, which I could not justify price-wise.
By Alan L. Peterson
Got the generator for lightning my power panel which I needed to replace. Worked fine the first 6 hours. Next day, fuel was running out of the carburetor. No expertise here, but took off float bowl, air cleaner cover, sprayed choke/carburetor cleaner, and applied air pressure . Still, same problem. Used flashlight and batteries to finish my panel wiring. Next day took bowl apart and noticed gas inside the plastic float. Drained float and put a thin coat of Krazy Glue around the seam where it seemed to be leaking. With a smile, put it back together, but same problem of leaking gas around the carburetor. Next day, took bowl apart, experimented with the float tang that regulates gas flow at the pin valve, and finally success. Local small engine repair folks told me they knew of nothing that would work other than a replacement float. Had used similar glue on an outboard motor lower gear housing and still working fine after several years.
By Sig (Arkansas, USA)
This works fine... we've used it to power ham radio gear during a 36 hour race. Very small and gets great "gas mileage" when using it to power a 2m mobile and a few lights.
By David Hollfelder (Austin, TX)
Received my $118 (incl shipping) bargain "Chinese" generator from Amazon, NIB. Found it had been dropped, the foot had sunk (smashed) thru the styrofoam packing. The front panel including the air cleaner area was cracked with a piece broken off. Started and tested OK - actually runs very well. Called Amazon, "she" asked me "if I send the parts at no charge, can you fixit yourself?" I said yes.
BTW, Purchased the generator to power LiPoly battery chargers - charge RC airplane batteries at the flying field - many, of not most flying fields do not have electricity.
1) after one "run", the fitting attached to the fuel tank (above the petcock) started leaking. The connection was not tight enough. This is a straight ttread (not pipe thread) with a rubber "compression" bushing. After removal, I wound teflon tape around the threads, and under the place where the rubber compression grommet goes, so that when fitting was screwed into the gas tank, the threads were very tight fitting (because of the teflon tape) when hand tightened. When all was aligned, tightened with wrench to apprx 8 or 10 ft-lb.
2) Replacement panel was not exactly the same - had to fabricate new mounting for the capacitor, and power plug cover, and several other tweaks to get all to fit.
Disturbing Discovery; the wiring was not packed/secured properly - wiring was in contact with several vibrating parts, causing the wiring insulation to begin wear away (chafe) - this would eventually cause a "ground out" (cause a short to ground).
Once the front panel was repaired, and in place --- read on
** repairmans "pro" tip **. Remove the gas tank so you have access from the top. Cover the power wires with large shrink tubing (so it fits over the power wire(s) connectors) and tie wrap (somewhat loosely) - be sure that no wires touch the engine/generator or fuel tank (protect insulation from chafing), Then put gas tank on last. Inspect wiring using flashlight to double check that no wiring is touching anything where vibration would wear away the wire insulation.
Finally, I'm still pleased with the generator considering the price. I just had to finish the "quality".
By Mark J. Potaznick
I bought this for use on a scoreboard for my local Little league. Works like a charm. Very quite. starts right up. Never a problem. Highly recommend this item. For the price you can not do better.
Images Product
Check Price ETQ TG1200 1,200 Watt 2 HP 2-Cycle Gas Powered Portable Generator (Non-CARB Compliant) Now!!
0 comments:
Post a Comment